显示标签为“multi-arc ion metallization vacuum coating machine”的博文。显示所有博文
显示标签为“multi-arc ion metallization vacuum coating machine”的博文。显示所有博文

2017年1月10日星期二

Let coating equipment maintenance has a higher value

Let coating equipment maintenance has a higher value
Each device has its own life, maintenance purpose is to maximize equipment performance and potential to improve the efficiency of the use of time and the value has risen considerably.
We often find that some coating plant equipment dirty, lots of grease, a lot of dust, many employers feel that as long as the equipment can do on the line, so clean out is no relationship between the external and internal, a complete waste of time is not necessary, did not realize the device from dust and grease will have an impact, it will reduce the life and performance of the equipment.
For maintenance coating equipment, maintenance and repair must have routine maintenance and periodic maintenance, equipment, the most important is attentive to the key analytical issues, well you can take a lot less detours, I believe that every teacher have deep get experience.
Routine maintenance coating equipment, for the conventional part of the day should be no time to check, for example, the oil will not be less, if the day was found in the production facilities have an adverse signs, even a little problem should be resolved immediately, less oil To add promptly, although oil is periodically replaced, parts can see a problem and do not work properly and so thoroughly broken in change, a problem may cause a chain reaction of problems arise more big losses, saying the remedy is better cooked rainy day.
Regular maintenance coating equipment, routine maintenance is not a substitute for regular maintenance, routine maintenance is shallow, regular maintenance should be deeper, who do not want to see is the machine problems in production led to production planning affected, coating operational status of the device directly affect product quality, production schedule, to ensure good operation of the equipment, establish and improve equipment maintenance and repair systems, standards are a must.
Many coating equipment pre-qualified, but often fails, coaters are not withstand even the best choice to use a lot of problems have appeared in the daily use, the machine does not allow the normal flow of work, there is no maintenance of equipment over . In good equipment is not withstand the toss, do not let the cold equipment at a critical moment, a little short of time to spend a day in maintenance equipment, perhaps unexpected potential value.

2016年12月26日星期一

How to reduce the vacuum coating of dust?

How to reduce the vacuum coating of dust?
Through long-term practice, summed up dust factors affecting the effect of vacuum evaporation coating machine coating and matters needing attention:
1. The coating after a period of time, the inner wall of the vacuum coating machine must be clean;
2. The staff have special clothing, light coating machine operation to wear gloves, socks, etc.;
3. Clean the substrate material, must be strictly accord with technical requirements;
4. Use the purity of source materials to meet the necessary requirements;
5. The sample out after placing environment to pay attention to the problem of clean;
6. The appropriate increase the humidity environment, multi arc ion coating machine can lower the suspended solid particles of the surrounding environment;
7. Technically explicitly allow maximum particle size and the number of particles per unit area of the ceiling is roughly how much;
8. The indoor air flow is low, the ground clean, splash control sputtering coating machine if it is a bare concrete, need to deal with the cover. Walls, roofs, cannot use the general grey coating paint.

2016年12月8日星期四

Vacuum coating equipment choice points

Vacuum coating equipment choice points
▲ optional double water-cooled furnace body structure made of stainless steel, carbon steel, or combinations thereof of.
▲ resistive and inductive heating in the form of two kinds, resistance heating materials molybdenum wire (band), tungsten (band), a graphite rod (plate), tantalum rods, nickel chromium wire (with) several types according to different temperature and process requirements for selection.
▲ heat insulation layer metal and composite two, choose according to different process conditions.
▲ vacuum system consists of a mechanical pump, diffusion pump, oil booster, augmentations pumps, vacuum pumps, etc., and they are matched with a variety of pneumatic, manual, electric valves, piping, etc., can choose according to process requirements.
▲ temperature control system can choose different types of thermometer, temperature control and their sensing element.
▲ intelligent vacuum measurement optional digital vacuum gauge and measure the quality of regulation to ensure the accuracy of the degree of vacuum and product reliability.
▲ can be equipped with multi-point recorder for the whole process analysis, quality control and production management.
▲ According device characteristics, manual, semi-automatic, or a combination of control.
▲ according to the requirement with a variety of inflatable type, mass flowmeter, rotameter, to meet the inflation pressure controlled, multiple inflatable requirements.
▲ of water over-temperature, temperature deviation large, furnace, pumps, heat exchangers, etc., phase diffusion pump, furnace inflatable overvoltage, insufficient gas supply pressure, overcurrent and overvoltage, open circuit and other abnormal situations audible alarm and perform the appropriate protective measures.
▲ fast cooling system and the heat exchanger can choose natural cooling cycle mode, may be used for large-capacity electric furnace outer fast circulating cooling system to improve the cooling rate.

2016年11月30日星期三

Multi-arc ion coating machine for super hard film coating

Multi-arc ion coating machine for super hard film coating
Taking use of multi arc ion coating technology can do coating film on metal,alloy,and electrically conductive material(substantially non-conductive material) (using high-frequency bias). Multi-arc Ion plating film can be deposited by metal film, multi-alloy film, compound film; Can be single plated coating and also composite coating film can also be plated coatings and nano-multilayer co...ating gradient.
Vacuum ion plating equipment coating products, including drills, milling cutters, gear cutters, broaches, taps, scissors, shave blades, molds, injection molding, magnetic forming die, punching die, automotive and medical equipment, and other wear parts.
Ion plating technology is particularly suitable for the deposition of hard film. Ion plated hard and wear resistant coating film as super-hard anti-wear protection film is widely used in tooling, film tools, wear parts. Common membrane system comprises TiN, ZrN, TiAIN, TiC, TiCN, CrN, AI2O3 and the like. In addition, there are more hard DLC (DLC), TiB2 and carbon and nitrogen (CNX) film.
Ion plating technique can be applied in addition to ultra-epidural, and also for the preparation of other features, such as the head of the DLC protective film micro gyro bearings dry solid lubricant film (MoS2, DLC), and a variety of magnetic film series feature film, communications and electronic devices

2016年11月27日星期日

The harmfulness of coating machine

The harmfulness of coating machine
A large amount of gas or fuel will all be loss, high pressure gas storage or fuel gas cylinder and tank if there is a leak, caused a certain economic losses.
Internal to the device and atmosphere pollution caused by the only allowed to work in some gas, some microelectronics devices not only require work under certain pressure. Vacuum evaporation coating machine so that its internal to filling the maintenance of gas in general. However, due to the leakage hole presence of harmful gas in the external environment may leak through hole to the interior of the device or devices, and make the device internal gas composition changes, which cause pollution, make the device does not work even failure.
Arc ion coating machine type more atmospheric pollution environment these harmful substances into the atmosphere environment, containing flammable, explosive, toxic, radioactive and other harmful to people's physical health material storage tank once has the leakage. On atmospheric environment pollution, affects people health. Some inflammable, explosive qualitative leak detection, and burning and explosion may occur, endanger people life and peace.

2016年11月16日星期三

Vacuum Metallurgy Development Direction

Vacuum Metallurgy Development Direction
1.Certain specific process of metallurgical which is suitable vacuum metallurgy technology can be used in place of vacuum metallurgy technology.
2.Development of a new vacuum metallurgical equipment.
3.The new method,new equipment and new processes of vacuum metallurgy certain materials research....
4. Vacuum metallurgical development of new materials.
5 .There exists a vacuum smelting slag under conditions (including remelting) technology development
6. Reseaching new special smelting technology or Development of widing the same specialty applications technology .
7. Numerical simulation and computer control of special metallurgical smelting process and quality control.
8. Production of zero inclusions ultrapure superalloys and specialty steel.

A.Mitchell put forward the concept of zero production of stainless steel and high-temperature alloy inclusions, not only theoretically demonstrated obtain zero inclusion of stainless steel, and believed that if you can avoid the original stainless steel ultrapure metals into CaO or CaO-containing inclusions and high-temperature alloys.

2016年10月20日星期四

Vacuum coating machine coating principle is what?

Vacuum coating machine coating principle is what?

Vacuum coating machine coating principle is what? Vacuum coating machine is the product into during equipment widely used, with the rapid development of electronic industry, vacuum coating machine, coating quality gradually improve, so that we use in our everyday life come into contact with the plating products more and more.
In a sense, vacuum coating was also determined by the vacuum coating oil, in the vacuum coating, coating oil mentioned strong adhesive coating and the role of the metal film, it is in pieces at the bottom of the coating, plating and surface coating in the plating.
1. Vacuum environment
Vacuum environment is affecting the efficiency and results of vacuum coating, it is well known that vacuum coating is conducted under high vacuum coating, unit with Pa, the existence of the higher vacuum gas is less, for plating pieces of the influence of the lower.
2. The coating process
Vacuum coating unit into structure and vacuum coating technology with the constant progress of science and technology, is widely used advanced vacuum evaporation coating, vacuum ion plating and magnetron sputtering deposition, and so on, technology has adopted by the difference between different products, should the particular case according to the product to choose cost-effective coating process, which directly affects the vacuum coating machine of price and cost.

2016年10月8日星期六

Vacuum coating machine skill requirements

Vacuum coating machine skill requirements
1, the equipment of vacuum piping and static seal parts (flange, sealing ring, etc.) way of planning should be agree with GB/T6070 rules.
2, in the low vacuum and high vacuum and vacuum coating room on the road should be equipment vacuum measurement regulation, each part of the measurement of vacuum separation. When found that the electric field of measurement forms that trouble, should in the measurement of the inlet device electric field shielding device.
3, if the equipment of main pump used for dispersion pump, on the inlet side of the pump should be installed with oil steam trap trap
4, equipment of coating room should be equipped with observation window, baffle equipment shall be available. Observation window should be able to observe accumulation is the source of the assignment, and other key parts.
5, ion plating coating accumulation is the source of planning what needs to be able to progress in the process of ionization rate and utilization rate of progress of coating materials, reasonable matching accumulation is the source of power, reasonable placement accumulation is the orientation of the source in a vacuum chamber.
6, the reasonable heating equipment, usually heater programming should be plated workpiece temperature rise evenly Shared.
7, artifacts should be with vacuum chamber body insulation, workpiece frame planning should make workpiece membrane layer
8, ion coating equipment should have artifacts usually negative bias and ion bombardment power, ion bombardment power should have resisted the abnormal discharge equipment, keep the operation safe
9, all the parts of the vacuum chamber to meet different potential between the size of the insulation resistance value, all the 4.4.6 according to GB/T11164-1999
1, environmental temperature: 10 to 30 oc
2, relative humidity: no more than 75%
3, cooling water inlet temperature: no more than 25 oc
4, cooling water quality: the city tap water or appropriate quality of water
5, power supply: 380 v three-phase single-phase 50 hz frequency 50 hz or 220 v (used by electrical demand and decide); Voltage shaking size: 342-399 v or 198-231 - v;
Hz frequency shake size: 49-51.
6, the compressed air equipment, liquid nitrogen, cold water, hot water, such as pressure, temperature, consumption, etc., shall be in the product use manual.
7, equipment, environment, air cleaning, there should be no corrosion or cause electrical appliances and other metal parts appearance caused between metal conductive dust or gas exists.

2016年9月23日星期五

What to buy vacuum coating machine equipment should pay attention to?

What to buy vacuum coating machine equipment should pay attention to?
Large investment funds items, we will be very careful when buying, it would be ready before the purchase of the required detailed understanding of the work done, a vacuum coating machines are not cheap, with the fast development of vacuum coating industry, for the film to be coated product requirements are also gradually increase, for the use of materials is also gradually expand the scope, and that the vacuum coating machine to keep the product in terms of rhythm with a certain challenge. Now we have to introduce a few precautions to purchase vacuum coating machine.
First, the configuration of the vacuum system: quality and price will always be proportional, regardless of what kind of technology the purchase of machinery and equipment, evaporation or, ions or, magnetron sputtering, or, the same function of the machine, with different configuration, the price is definitely a difference. In general, the use of materials on behalf configured well, the natural life will be longer, the efficiency will be higher, film better.
Second, the vacuum coating machine housing: If the surface, basically difficult to see is good or bad, not only from the surface gives the visual effect to distinguish the case basically every vacuum equipment manufacturers can be processed out. For the case should focus on sealing, welding is very important, if you buy back the equipment found to have leakage problems that customers will be very headache, even indirectly, some inexplicable problems, causes leak occur often because processing not good. Therefore, customers choose to buy vacuum coating machine / coating equipment when we must focus on processing power.
Third, the core technology: the different processes used in the core is not the same, unified call evaporation source, but it is a target head or electronic guns. If you do not have good evaporation source, basically not try to complete the stable quality of the coating. Good evaporation source is needed after years of constantly improve and perfect coating of data and then come out, do not understand the process of evaporation source manufacturers difficult to do. If what manufacturers say that their equipment does not include the process, some do not buy it.
Fourth, field trips, samples proofing: Before you buy or coating equipment vacuum coating machine, take samples to coating, check the film coating system is not able to reach their own requirements, its technical service and after-sales service is not perfect, combined with the above mentioned consulting Consulting more points, the last shop around

2016年9月13日星期二

More arc magnetic control coating machine using and maintenance

More arc magnetic control coating machine using and maintenance
Its working principle is more arc magnetic control film coating machine under vacuum condition, using arc discharge and the working principle of glow discharge. On metal and nonmetal workpiece surface plating gold titanium nitride, titanium carbide, black 7 colour titanium oxide of nitrogen, etc. Yi ke anticorrosion plating film (such as AL, Cr stainless steel and TiN, etc.) and wear-resistant film, film layer and basal combined with strong, suitable for watches, metal, ceramic tableware and requirements of superhard grinding tool, mold and so on, has the very good development prospect.
Before using the power switch and action button should be in the off position, turn on the water, air, power supply.
1) open the vacuum control power switch.
2) start to maintain low vacuum in diffusion pump, pump and vacuum level before measurement.
3) for the front-end pressure after reaching 5.0 * 10 pa, heat diffusion pump.
4) open the charging valve, the coating chamber air, opened the door of coating chamber and packed clean artifacts, shut the door.
5) to the normal work of the diffusion pump after an hour, open open drainage mechanical pump valve, the vacuum chamber hand vacuum to 1.0 * 103 pa, then Cairo, pump.
6) when the pressure is 3.0 * 10 pa, after the closed drainage valve, open before class valves. Open the high, valve in coating chamber of high vacuum.
7) when the pressure in vacuum chamber reaches 8 * 10-3 pa open job rotation, and heating to the set value.
8) coating procedures.
9) end coating operation procedures.
10) drop temperature below 100 oc, remove the artifacts, open the charging valve door before each furnace used to clean the furnace.
11) after a work cycle, to clean the coating indoor dust suction vacuum, avoid short circuit or the vacuum system.
12) over a period of time to remove the barrier for cleaning.

2016年8月3日星期三

Analysis Principle vacuum coating equipment

                             Analysis Principle vacuum coating equipment

Principle is the principle of magnetron sputtering vacuum coating equipment , as follows:
Colliding electrons accelerated in the electric field toward the substrate during in and argon atoms, a large number of ionized argon ions and electrons, the electrons onto the substrate. Argon ions accelerated in the electric field bombardment target, a large number of target atoms sputtered, neutral target atoms deposited in a film on the substrate.
Secondary electrons accelerated toward the substrate in the process influenced by the magnetic force of the magnetic field Lorenzi, bound within plasma region near the target surface, a high plasma density region, under the effect of the secondary electrons around the magnetic field the target surface in a circular motion, the motion path of the electrons is very long, constantly in motion the process of collision ionization of argon atoms with a large amount of argon ion bombardment target, after several collisions electron energy decreases, get rid of the shackles of the magnetic field lines , away from the target, eventually deposited on the substrate.
Magnetron sputtering is bound to a magnetic field and to extend the path of movement of electrons, the electrons change the direction of motion, increase the ionization rate of the working gas and the efficient use of energy of the electron vacuum coating apparatus.
Electronic destination just substrates, the vacuum chamber wall and the target source anode is electronic home. But generally the vacuum chamber and the substrate and the anode potential in the same. Interaction between magnetic field and electric field so that a single spiral electron trajectory in three dimensions, and not only in a circular motion in the target surface. As for the type of the target surface sputtering the circumferential contour, and that the magnetic field lines are targets of the circumferential shape of circular. Distribution of magnetic field lines in different directions will film a great relationship.
Coating machine manufacturers said, not only in the interaction mechanism magnetron sputtering magnetic and electric fields of work, multi-arc plated target ion source, a plasma source and so work under this principle. The difference is that the electric field direction, voltage and current magnitude only.

2016年4月13日星期三

Widely applications of vacuum coating machines


  A lot of consumers know little about vacuum coating machine concept, do not understand uses of vacuum coating machine in the market;in fact there are a lot of derivatives of vacuum coating machines which are closely related with the consumer, coater buyers generally engaged in the following sectors: one category is mainly decorative, highlighting its decorative function, commonly used in plastic toys, gift wrap coating, cell phone case, digital products shell, windows, tiles and other gold-plated.
  Another feature is the main highlight of the function coating applications. Will be following industries: solar collector tubes, eyeglasses and lenses AR high back,increase the tools and moulds hard,the phone shell radiation shielding.
  Above two industries are closely related with the vacuum ​coating machines, so in life, vacuum coating machine is very important.

2016年3月14日星期一

Ion coating machine coating pretreatment process

               
  Working principle of ion coating machine is certain vacuum condition, by gas discharge, work or membrane material part of gas ionization, evaporation in the gas ion or material under the action of the bombardment of ions, the evaporation or reactants form a thin film deposited on the substrate surface. Ion coating machine coated in one of two ways, one is evaporation ion plating, the other is a sputtering ion plating. Evaporation is ion plating by heating membrane material, to produce metal steam, and then through different ways to motivate steam discharge, ionization deposited into a film. Sputtering ion plating is produced by high-energy ion sputtering film material on the surface of metal particles, then in gas ionization discharge space into a metal ion, the deposition film on the substrate. Vacuum ion plating for sedimentary hard film, widely used, such as cutting tools, wear-resistant parts surface.
Before with ion coating machine made plating film, is needs a sample test according to the needs of users, the following brief introduction:
1, first, and customer communication, to understand the performance and usage of samples;
2, analysis of samples, the performance, surface state, etc.;
3, choose before processing link;
4, depending on the type of surface shape, pollutants such as choosing pre cleaning;
5, test before treatment effect;
6, test samples, if qualified, compiling process, formally put into production.